Inflatable Game Set-up and Tear Down Instructions

Tear Down Instructions


Step 1: Remove stakes from corners of the inflatable.. Turn off the blower. Disconnect the inflation tube from the blower. Open all ports to allow air inside game to come out freely. Allow 10 - 15 minutes for the game to deflate. After game is on the ground step on the areas that still have air in them.	Step 2: Continue to step on game to get the air out. Pull all of the sides into the middle of the bounce. You should be able to see the seam of the bottom of the game. The flatter you are able to make game, the easier it is to roll it up.


Step 3: Fold in steps and inflation tubes	Step 4: Starting from the right side of the game, fold the game approximately 1/2 of the width of the game to the middle of the game.


Step 5: Fold the left side of the game to the middle of the game.	Step 6: Fold the left side on top of the right side.


Step 7: Step on the inflatable to flatten the game out and squeeze any remaining air.	Step 8: Make sure that all ports, ropes, or hanging parts are tucked into the bounce.


Step 9: Starting at the front of the game, roll as tight as you can get it.	Once you get started it rolls fairly easily.


Step 10: Once the game is completely rolled. Place the strap around the bounce, feed the end through the ratchet portion of the strap and pull it as hard as you can.	Step 11: Once the strap is as tight as you can get it. Start ratcheting the strap until the strap is tight. Do not over tighten the strap because it may cut the game or it will be very hard to undo later. Place into bag if one is provided.

Locate Suitable Plot	Set Up Instructions Must be Level, Flat, and Near Electrical OutletSource. Be aware of potential problems such as tree roots on the surface, overhead tree branches, or power lines. Be sure not to place Spacewalk at the Bottom of your land's grade. Doing so may cause possible water retention.
Clean, & Clear Surface	Remove any Obstruction that may be of potential danger or problem to inflation of game.


Setting Up Your Inflatable.Amusement
Unload Spacewalk	Use caution when transporting Inflatable to your set-up site. Rather than lift the entire Inflatable, please wheel it around, or roll & flip it into position from place to place. It is recommended that at least two or more individuals participate in the transport phase. However, in situations where help is unavailable, please do not attempt to lift. Rather, please use a wheel cart or at least use the roll and flip method. This is not a Rigid object. You'll be lifting "Dead Weight".
Lay Out Tarp	For protection from friction and severe wear, you must first layout the tarp if provided as a surface base.
Lay Out Tarp	Make sure the surface is flat and free of any obstructions. (Such as Rocks, Sharp Objects, Trash, Tree Roots, etc.) Now is also a good time to double check any overhead obstructions. (Such as limbs, Cables, Wires, etc.)
Align Inflatable before Unrolling	Consider the direction your Inflatable will face in proportion to your event layout and be aware of where your Electric Outlets for your power source are located. Your Air Duct Tubes, once visible, should be positioned towards the same direction where your blower will be set up near the power source. Another factor is the position of your Inflatable’s entrance Doorway.
Un-Roll onto flat Surface	Two people may provide the best results for unrolling inflatables flat unto the ground. However, if help is not available, unrolling may be made easier by an individual worker by using the crawling method.
Pull Out and Spread	Pull out and spread game from floor corners and roof corners until you have aligned and centered the inflatable on top of the tarp. Again, be aware of the direction and location of doorway and Air Duct Tubes.
The Turbo Blower Motor	This Electric Blower Motor uses 110 v standard current. Be aware that it is not advised to use more than one electrical device in the same outlet. This Blower Unit requires more amps than your usual household appliance, so to prevent setting off the breaker, and/or to insure that unit draws enough power, please leave Blower Unit independent of any other electrical items in the same outlet. Also, DO NOT use excessive lengths of power cord(s). Keep Unit as close to Outlet as possible!
Pull Air Duct Tube Over Mouth of Blower Motor	If Your Inflatable game has Two Air Duct Tubes, choose the tube closest to your power source. (If it is convenient for you). Grasping the open end of the Air Duct Tube, Pull Tube inward to the base of the mouth of the blower motor.
Clip Belt Strap Together	On most Air Duct Tubes, you’ll see a hook and buckle type of fastener. Connect them together now. Other Air Duct Tubes require you to thread the belt strap through the buckle. If yours is like that, strap it at this time.
Tighten Belt Strap	Pull the slack side (Movable side) of the Belt Strap until the belt is tightly bound around the mouth of the Blower Motor.
Tie Off Unused Air Duct Tube	If your Inflatable has Two Air Duct Tubes, Now is the time you must Tie Off the unused tube. (This is the tube which is farthest from your power source, so it is not needed)
Flip the Toggle Switch to the "ON" position (On most Blowers)	On most models of Blower Motors, you’ll easily find The ON/OFF toggle switch located on the side (in a recessed area), Or on the outside-top. Flip it to the “ON” position and keep the blower turned ON the entire time your Inflatable is in use. As soon as you turn the switch off, the Inflatable will begin to deflate. The "Black Box" Style Blower has no switch and only requires plugging into a socket to turn ON. (Leave plugged in and running while in use).
Guide Upward as it Inflates	To prevent tangling, tearing or catching outside objects, please guide the Inflatable Upwards and spot check to make sure that your game is clear of all obstructions which may catch the product during it’s upward inflation movement.
Drive Security Stakes into Ground at Corners after Stretching Out flat & taut	Now that the full width of the game has been expanded by air, you’re able to see exactly where to place your security grounding stakes. Drive the four stakes through the loops in the corners with a hammer.
View of the Two Air Tubes. Utilizing One Blower tube while extra tube is tied off in the Rear	This illustration shows the proper tie down and Set-up of Blower and Air Duct Tubes. * NOTE * Do Not use small extension cord(s). The Cord must be Heavy Duty with three prongs (w/ ground). Blower requires high amps, so do not over extend the length by adding too many cords. Do not insert other electric items in the same socket. Blower requires it’s own independent socket without overloading.
Proper Use
Use Care and Caution!	Must have Adult Supervision at all times! Occupants must remove their Shoes. No entering with hard or sharp objects in clothing or in hands. No food or drinks inside. Keep minimum occupancy to reduce the probability of injury. Keep the same age group of height and weight children grouped together. Do not place large children together with very small children. No infants allowed.
BE SAFE! HAVE FUN!